0086-21-58386256
This is a pretty thorough discussion of the PC Mill 50. Accoring to discussion I had in the past with Emco USA, the only difference between the PC Mill 50 and the newer PC Mill …
Do somebody have the compleet electrical schematics of the Emco PC55 Mill so that I can convert it to Mach3 whit less modification. Did you ever convert your PC55 Mill? I have a schematic.
The ISA cards are different for the PC Turn 50 - RS485 - and PC Turn 55 - RS422. These cards are not standard cards which can be purchased off the internet, they are the specific Emco versions using the RS485/RS422 protocols.
I am in the middle of retrofitting an EMCO PC Turn 55 to runing EMC2. I am using a G540 for control and a VFD to run the spindle motor. Both axis move and EMC...
Iv an Emco PC Turn 55 I am retro fitting with Linuxcnc. It comes with a 3 phase AC motor. I can't seem to find the specs of the motor. I'm sure it's either 50hz or 60hz. I have a VFD setup. If I run the motor at 50hz, the spindle is at about 1200rpm on the fastest pulleys. If I double the frequency to say 100hz. Will this damage the motor?
I have the PC Turn 55 with the electronic version A6P_V01, which uses three-phase motors like the ones I put in the photos, which were still used in the Concept Turn 55.
Iv an Emco PC Turn 55 I am retro fitting with Linuxcnc. It comes with a 3 phase AC motor. I can't seem to find the specs of the motor. I'm sure it's either 50hz or 60hz. I have a …
I am in the middle of retrofitting an EMCO PC Turn 55 to runing EMC2. I am using a G540 for control and a VFD to run the spindle motor. Both axis move and EMC controls the spindle just fine with M3 and S commands.
Picked up an Emco pc turn 55 with 8 position turret for 425 bucks. No controller, so swapped the ac95 board with a mesa 7i76ed, interfaced with the 3 phasen sm karte with an idc16 ribbon cable breakout board and got the motors to move pretty easily.
So as the title says i have an EMCO pc mill 55 cnc. I am in to process of fixing the machine. I have rebuilt the controller pc and got it working. I have now moved onto the …
I have the PC Turn 55 with the electronic version A6P_V01, which uses three-phase motors like the ones I put in the photos, which were still used in the Concept Turn 55.
I will tell you about the Emco PC Turn 55 retrofit project in this thread. The lathe was in very good condition. I changed the keep plates because the original ones, which are …
The ISA cards are different for the PC Turn 50 - RS485 - and PC Turn 55 - RS422. These cards are not standard cards which can be purchased off the internet, they are the specific Emco …
So as the title says i have an EMCO pc mill 55 cnc. I am in to process of fixing the machine. I have rebuilt the controller pc and got it working. I have now moved onto the machine itself.
With its extensive product portfolio, the EMCO Group is a respected and proven partner within the field of turning and milling. 65 Models View more about Emco Sales Offices and …
This is a pretty thorough discussion of the PC Mill 50. Accoring to discussion I had in the past with Emco USA, the only difference between the PC Mill 50 and the newer PC Mill 55 was the interface card/circuitry used to connect the mill to the pc.
I am in the middle of retrofitting an EMCO PC Turn 55 to runing EMC2. I am using a G540 for control and a VFD to run the spindle motor. Both axis move and EMC controls the …
Do somebody have the compleet electrical schematics of the Emco PC55 Mill so that I can convert it to Mach3 whit less modification. Did you ever convert your PC55 Mill? I …
I will tell you about the Emco PC Turn 55 retrofit project in this thread. The lathe was in very good condition. I changed the keep plates because the original ones, which are made of plastic, were broken. I made the new ones with an anti-friction plastic from Igus.
I recently acquired a PC Turn 55 Lathe and PC including the control card and have been slowly getting it back to working condition. Spent a few days repairing the PC and got it …